Epifanes Varnish Clear 250 ml
Description
A clear, high gloss, traditional one-component varnish, based on tung oil, phenol and alkyd resin with excellent outdoor durability, containing an ultra violet filter protecting the wood against discolouration. For use on bare wood & intact existing (one and two component) varnishes both for inside and outside above the waterline. This varnish is famous for its high gloss retention, long lasting properties, unique flow characteristics and high build capacity even in tropical climates.
Thinner : Brush application - Epifanes brush thinner for paint & varnish.
Spray application - Epifanes spray thinner for paint & varnish.
Recoatable : After 24 hours at 18°C (65°F.).
Coverage : One liter is sufficient for 14 m² (150 ft²).
Coats | First | Second | Third | At least 4 more |
Product | Epifanes Clear Gloss | Epifanes Clear Gloss | Epifanes Clear Gloss | Epifanes Clear Gloss |
Thinner | Brush Thinner For P&V | Brush Thinner For P&V | Brush Thinner For P&V | Brush Thinner For P&V |
Thinning Ratio % | 50 | 25 | 15 | 0 - 5 |
Drying Time hrs | 24 at 65F./18C | 24 at 65F./18C | 24 at 65F./18C | 24 at 65F./18C |
Abrasive paper grit | 220 | 280 | 320 | 320-400 |
Abrasive type | Dry | Dry | Dry | Wet or Dry |
Coverage/liter | 150 - 300 sq. feet | 150 - 250 sq. feet | 150 - 200 sq. feet | 150 sq. feet |
Remarks | Do not sand through the stain | Sand by hand. Machines can be too aggressive. |
Maintenance:
If existing coats of varnish are intact, one or more coats may be applied on a well cleaned, degreased and lightly sanded surface.
For annual maintenance, apply a minimum of one or two coats of Epifanes Clear Gloss Varnish, following surface preparation instruction.
The number of maintenance coats needed depends on the condition of the varnish system.
Epifanes Clear Gloss Varnish may also be applied on any well cleaned, degreased and sanded two-component varnish.
The weather and atmospheric conditions to which the finish is subjected will determine the amount of time between coats.
An existing varnish system in poor condition must be removed. Weathered spots may be treated with a cleaning or bleaching product.
If either are used, wash down the surface thoroughly with fresh water in order to remove any residue. Allow the surface to dry.
Smaller spots needing repair may be filled with several coats of varnish.
When an equal level has been achieved, sand to a smooth surface and apply one or more coats of varnish on the entire surface.
-
General Specification
Coats First Second Third At least 4 more Product Epifanes Clear Gloss Epifanes Clear Gloss Epifanes Clear Gloss Epifanes Clear Gloss Thinner Brush Thinner For P&V Brush Thinner For P&V Brush Thinner For P&V Brush Thinner For P&V Thinning Ratio % 50 25 15 0 - 5 Drying Time hrs 24 at 65F./18C 24 at 65F./18C 24 at 65F./18C 24 at 65F./18C Abrasive paper grit 220 280 320 320-400 Abrasive type Dry Dry Dry Wet or Dry Coverage/liter 150 - 300 sq. feet 150 - 250 sq. feet 150 - 200 sq. feet 150 sq. feet Remarks Do not sand through the stain Sand by hand. Machines can be too aggressive. Maintenance:
If existing coats of varnish are intact, one or more coats may be applied on a well cleaned, degreased and lightly sanded surface.
For annual maintenance, apply a minimum of one or two coats of Epifanes Clear Gloss Varnish, following surface preparation instruction.
The number of maintenance coats needed depends on the condition of the varnish system.
Epifanes Clear Gloss Varnish may also be applied on any well cleaned, degreased and sanded two-component varnish.
The weather and atmospheric conditions to which the finish is subjected will determine the amount of time between coats.
An existing varnish system in poor condition must be removed. Weathered spots may be treated with a cleaning or bleaching product.
If either are used, wash down the surface thoroughly with fresh water in order to remove any residue. Allow the surface to dry.
Smaller spots needing repair may be filled with several coats of varnish.
When an equal level has been achieved, sand to a smooth surface and apply one or more coats of varnish on the entire surface.
Product Options
Product | OEM | EEPN | Availability | Price | Qty |
---|---|---|---|---|---|
CV.250
|
13.02.0010
|
AED 51.00
|
|
||
CV.500
|
13.02.0011
|
AED 81.00
|
|
||
CV.1
|
13.02.0012
|
AED 148.00
|
|
||
CV.5
|
13.02.0013
|
AED 673.00
|
|