Exalto Emirates LLC.

0 Items

Products added to your cart

0 Items

You have no items in your shopping cart.

Sensors


  • The Vetus ultrasonic level sensor, SENSORA & SENSORB are contactless and will measure the fluid level in any type of tank. It is suitable for use with: petrol, diesel fuel, drinking water, black and grey waste water. After installation, the sensor can be calibrated very easily with the aid of a LED and a calibration wire; no other equipment is required. The sensor may be installed in any type of tank, regardless of its dimensions, but with a maximum depth of 120 cm. The sensor may be connected to all standard Vetus analog level indicators and also to the Vetus waste water control panel (WWCP). These sensors are not suitable for use with metal tanks.

    (3 items) from AED 639.00
  • The display instrument (SENSORD) can be used to show the contents of up to 4 different tanks and can be used in conjunction with SENSORB.

     AED 2,562.00
  • (2 items) from AED 269.00
  • For use with Vetus rudder angle indicator

     AED 1,253.00
  • Temperature sensor for batteries with 15m cable

     AED 226.00
  • The arm length is adjustable between 200 and 412 mm.. All Vetus tank level indicators are matched with Vetus tank senders and can be connected directly to each other to give an accurate reading. To connect non-Vetus level indicators to a Vetus tank sender, it is necessary to install a 10.09.0066 signal converter in the circuit

     AED 755.00
  • Float for application in all rigid petrol and diesel fuel tanks with a height between 140 and 660 mm. Both the vertical strip and the horizontal float arm are completely adjustable. Add resistance: 240 Ω to 44 Ω. All Vetus tank level indicators are matched with Vetus tank senders and can be connected directly to each other to give an accurate reading. To connect non-Vetus level indicators to a Vetus tank sender, it is necessary to install a 10.09.0066 signal converter in the circuit.

     AED 176.00
  • Liquid level senders are level indicating devices compatible with all the petrol and water level gauges available on the market. They are fuel, sea-water and acid resistant because they are made of the highest stainless steel AISI 316. They are perfectly watertight and have a flange with holes that allows a perfect fitting on the tank. The sender cables must be connected to the measuring terminals of the indicating instruments

    (78 items) from AED 247.00
  • To connect non-Vetus level indicators to a Vetus tank sender, it is necessary to install a signal converter in the circuit

     AED 221.00
  • The BG-SWA (Solid-State Bilge Pump Switch with High Water Alarm) is a highly reliable bilge pump switch that is the ideal replacement for unreliable mechanical float switches with an integrated high-water alarm. The BG-SWA uses two integrated sensors to detect liquid in the bilge while reliably activating the bilge pump. Having no moving parts that can be jammed or damaged, the solid-state BG-SWA is built to outlast all the mechanical float switches on the market today while alerting you of water presence in your bilge. The BG-SWA is CE and ISO 8846 Marine Ignition Protection Certified, tested to ABYC-1500 standards. Patented technology. The BG-SWA will activate the bilge pump when water or any liquid is detected. The BG-SWA triggers the high-water alarm when water is detected continuously for 3 seconds after the first detection (factory default setting) indicating that the bilge pump is either overwhelmed with excessive rising water or not working. Based upon bilge and pump size, the user can configure the alarm activation delay from 3-10 seconds. The BG-CP is recommended to display and sound the alarm. Users can use their existing panel with equivalent functions. The alarm output of the BGSWA is a 12 or 24 Vdc with 1-amp max drive. The BG-SWA can be tested and its status can be viewed using the BGI Config App, which can be downloaded from the App Store or Google Play. The App is used on a mobile device with Bluetooth to wirelessly connect to the BG-SWA device. The App will report the input voltage level and system temperature. It also allows changing the name of the device for easy identification and testing the device. Set the pump run time after water detection via the BGI Config App. The high-water alarm timing can be configured via the BGI Config App. The configurable range is 3-10 seconds. The BG-SWA also offers programmable splash protection, which can be used in rough waters or foul weather conditions to prevent false pump activation which can result in the pump running dry. Splash protection modes include High (2 seconds, factory default setting), Medium (3 seconds), Low (5 seconds), and OFF.

     AED 936.00
  • The BG-SW (Solid-State Bilge Pump Switch) is a highly reliable bilge pump switch, with no moving parts, that is the ideal replacement for unreliable mechanical float switches. The BG-SW uses two integrated sensors to detect liquid in the bilge while reliably activating the bilge pump. Having no moving parts that can be jammed or damaged, the solid-state BG-SW is built to outlast all the mechanical float switches on the market today. The BG-SW is CE and ISO 8846 Marine Ignition Protection Certified, tested to ABYC-1500 standards. Patented technology. The BG-SW will turn the bilge pump ON when water or any liquid is detected and turn OFF when no water or liquid is detected. The BG-SW extends the life of the bilge pump due to its ability to significantly reduce current spikes during the activation of the pump. The BG-SW can be tested and its status can be viewed using the BGI Config App, which can be downloaded from the App Store or Google Play. The App is used on a mobile device with Bluetooth to wirelessly connect to the BG-SW device. The App will report the input voltage level and system temperature. It also allows changing the name of the device for easy identification and testing the device. Set the pump run time after water detection via the BGI Config App.

     AED 835.00
  • The BG-One (Oil and Fuel Detector with Smart Bilge Pump Switch) integrates with the bilge pump system to selectively pump out water and not oil or fuel, preventing the vessel from accumulating water and aiding in the prevention of costly oil or fuel spills. The BG-One was developed in collaboration with the marine industry needing a reliable, long lasting bilge pump switch. Having no moving parts or float switches that can easily be damaged, the BG-One will automatically turn off the bilge pump when oil or fuel is detected before a costly spill occurs. The BG-One will connect to any 12 or 24 Vdc bilge pump and alarm panel on the market today. The BG-One is CE and ISO 8846 Marine Ignition Protection Certified, tested to ABYC-1500 standards. Patented technology. With precise oil and fuel detection accuracy down to 1 mm (0.04”), the BG-One minimizes the boat owners’ liability for costly cleanup and possible fines; all while extending the life and reliability of the bilge pump through selective pumping. When the sensor is configured in its factory default mode, Mode A (Marina), the pump will turn ON when water is detected and turn OFF when oil or fuel is detected. The pump will turn back ON when only water is detected. In Mode B (Marine Sanctuary) the pump will turn ON when water is detected and turn OFF when oil or fuel is detected. The pump will remain OFF until the alarm and bilge are cleared (requires power cycling of device). In Standard Mode (High Seas) the pump will turn ON when any liquid is detected and turn OFF when there is no liquid detected. Set low, medium, or high oil detection sensitivity via the BGI Config App. Set the pump run time after water and oil detection via the BGI Config App.

     AED 1,108.00
  • The USCG 46 CFR 28.250 & 182.530 compliant BG-HW (High Water Sensor) detects salt or fresh water and can be easily integrated into any vessel’s alarm system. Water in any compartment of a vessel is a potential crisis. Early warnings of water entering the hull or leaking from plumbing is extremely important for the safety of the vessel and passengers. The BG-HW is CE and ISO 8846 Marine Ignition Protection Certified, tested to ABYC-1500 standards. Patented technology. The BG-HW triggers an alarm when high water is detected, once connected to a BG-CP (Control Panel) or any alarm system. The BG-HW has a 12 or 24 Vdc with 1-amp max alarm output.

     AED 784.00
  • The BG-Oil (Oil and Fuel Detector) senses the presence of oil and can be easily integrated into any vessel’s alarm system. Compartments on a vessel or even in a landside space are often in close proximity to tanks and machinery where oil and fuel leaks can potentially occur. Installing the BG-Oil will provide an early warning for spills in these environments. The BG-Oil is CE and ISO 8846 Marine Ignition Protection Certified, tested to ABYC-1500 standards. Patented technology. With precise oil and fuel detection accuracy down to 1 mm (0.04”), the BG-Oil triggers an alarm when oil or fuel is detected, once connected to a BG-CP (Control Panel) or any alarm system. The alarm output sources up to 1 amp, making it capable of driving user relays and actuators. When the sensor is configured in its factory default mode, Standard Alarm Mode, the alarm will turn ON when oil is detected and OFF when oil is no longer detected. In Latch Alarm Mode the alarm stays ON when oil is detected, until manual reset or power cycling of the devices. Set low, medium, or high oil detection sensitivity via the BGI Config App.

     AED 886.00

Close

Share this page

Dear Friend,

Check out this awesome new product from Exalto Emirates!

Page: 04 Sensors
Share to
Your detail
Close

Specifications

Specifications

Close