Exalto Emirates LLC.

0 Items

Products added to your cart

0 Items

You have no items in your shopping cart.

Tanks & Accessories


  • This new range of tanks is made of thick walled high grade linear polythene, which is both rust free and less prone to condensation compared with metal tanks. These tanks are suitable for regularly available diesel fuel up to 100˚C. The construction of the tanks is seamless and therefore can never leak. The fuel level can be seen from outside for easy checking. The ATANK range is also suitable for drinking or waste water. The tanks are supplied with labels which are used to specify the tank contents (diesel, fresh water or waste water). When labelled for diesel fuel and with the new inspection lid type ILT installed (see below), all tanks meet the requirements of the ISO 21487 standard. The tanks are supplied without fittings and therefore these can be installed wherever you choose. • The tank is suitable for diesel (up to 100°C), waste water and fresh water• With just one code you can order your diesel tank, waste water tank and fresh water tank• The wall thickness prevents permeation and odours and distortion of the tank• Available with a capacity of 42, 61, 88, 110, 137, 170, 215, 335 and 390 liters.

    (9 items) from AED 400.00
  • This range of rigid drinking water tanks is available in different shapes and sizes. They are supplied without fittings and therefore these can be installed wherever you choose. The synthetic material is suitable for drinking water and meets the KTW standard. The construction of the tank is seamless and will never corrode or leak. The water level can be seen from outside for easy checking and the tank is easily cleaned through the inspection lid. A connection kit (04.04.0016) should be ordered separately for each tank, together with additional inspection lids (WTK02 or WTKIT) if required. The 88, 137 & 335 liter models are provided with a baffle, as a standard construction element.

    (9 items) from AED 558.00
  • This range of rigid Vetus tanks is designed for drinking water. The high-grade linear polythene materials used are the same as all other rigid Vetus tanks and they are available with capacities of 40, 60 or 80 liters. These tanks will save considerable installation time! The center point for a SAE flange gauge sender is incorporated in the moulding together with 5 blind bolt holes. The relevant gauge sender should be ordered separately and the appropriate hole cut in the tank. Each tank is supplied with the following connections:• Fixed hose connector Ø 38 mm for filling.• Fixed hose connector Ø 16 mm for the breather line.• Rotating hose connector Ø 13 mm with pick-up pipe, for water suction.These tanks come complete with a screw down inspection lid installed.

    (3 items) from AED 972.00
  • This high grade synthetic tank for drinking water is supplied with an electric pump which automatically switches on when the pressure in the system drops (for example when a tap is opened).• Output 13.2 ltr/min at zero head.• Pump pressure 3.1 bar.• Connections for filling line Ø38 mm, outlet line Ø13 mm and ventilation line Ø16 mm.• Also supplied with inspection cover, float sensor, connectors and filter in suction line.

    (8 items) from AED 1,468.00
  • These tanks can be installed easily and quickly; they assume the shape of the space, in which they are placed and they can be positioned in places that are normally difficult to reach. Also, generally speaking, there is no need for any additional installation parts. In fact, fitting the outlet nipple and connecting the hoses for inlet and outlet are the only things to be done. Each Vetus flexible drinking water tank has two right angle nipples as standard supply: one for connection to the filling pipe (Ø 38 mm) and the other one for connection to the pump hose (Ø 16 mm). The filler nipple comes fitted to the top of the tank and the other one is supplied loose for easy fitment in any desired position. The fabric of Vetus flexible water tanks consists of three layers:1. A wear resistant layer2. A reinforcement layer3. Suitable for contact with drinking water.

    (8 items) from AED 500.00
  • These Vetus tanks are made in 9 different shapes and sizes, with contents of 137,335 or 390 liters. Provided with ISO 8099 identification.

    (9 items) from AED 501.00
  • The high-grade linear polythene materials used are the same as all other rigid Vetus tanks and they are available with capacities of 40, 60 or 80 liters. The center point for an SAE flange gauge sender is incorporated in the moulding together with 5 blind bolt holes. The relevant gauge sender should be ordered separately (please refer to the Monitoring & control category) and the appropriate hole cut in the tank. These tanks will save considerable installation time. Each tank is supplied with the following connections: Fixed hose connector Ø 19 mm for the breather line. Rotating hose connector Ø 38 mm with pick-up pipe, for waste water suction. A Ø 42 mm hole is provided for easy installation of an inlet fitting, type RT..B. This should be ordered separately according to the inlet hose diameter (Please refer angled fittings in toilet accessories section). If required, additional inlet fittings may also be installed. These tanks come complete with a screw down inspection lid installed. Provided with ISO 8099 identification.

    (4 items) from AED 810.00
  • These tanks are available in 3 sizes, with capacities of approximately 25, 60 or 80 liters. The tanks are made of odour impermeable polythene and the contents level can be seen from outside. These tanks are suitable for mounting under the side decks, above the waterline. When permitted, the contents of the tank can be gravity discharged at sea, without the assistance of a pump. Simply opening the sea cock will empty the tank. Provided with ISO 8099 identification.• Suction pipe with Ø 38 mm angled hose connector, for connection to deck plate• Angled hose connector, Ø 38 mm, for discharge• Inspection cover• Angled hose connector, Ø 19 mm, for tank ventilation (breather)

    (4 items) from AED 1,189.00
  • The tanks are made of odour impermeable polythene. The system comes complete with a Vetus waste water pump type EMP (12 or 24 V), an inspection cover, a tank gauge sender (the 12 or 24 Volt level gauge must be ordered separately, please refer to the Monitoring & control category), a plastic suction pipe with Ø 38 mm angled hose connection for discharge from ashore, two securing straps and one Ø 19 mm connection for the breather. Angled connectors for the input of waste water must be ordered separately (Please refer angled fittings in toilet accessories section). One hole has already been provided, to connect the inlet fitting. These waste water systems are designed to save on space and installation time and are available with tank capacities of 42, 61, 88 or 120 liters. All input and discharge connections are accessible at the top of the tank. Provided with ISO 8099 identification. Model WWS is not only suitable for storing “black” water, but also for “grey” waste water.

    (8 items) from AED 4,451.00
  • Vetus flexible tanks for grey and black water are constructed in the same way as the flexible drinking water tanks. However the material used is suitable to store waste water and is odour tight.  1. Two right angle nipples Ø 38 mm (supplied with each tank)2. Right angle breather nipple Ø 16 mm, already fitted.3. Breather nipple Ø 16 mm.4. Breather bend for anti-siphoning device, When discharge of the tank through a deck plate is required, a Ø 38 mm tank connector is available as an option(Please refer angled fittings in toilet accessories section).

    (4 items) from AED 758.00
  • This range of rigid Vetus tanks is designed for diesel fuel. The high-grade linear polythene materials used are the same as all other rigid Vetus tanks and they are available with capacities of 40, 60 or 80 liters. The center point for an SAE flange gauge sender is incorporated in the moulding together with 5 blind bolt holes. The relevant gauge sender should be ordered separately (please refer to the Monitoring & control category) and the appropriate hole cut in the tank. These tanks will save considerable installation time. Each tank is supplied with the following connections: Fixed hose connector Ø 38 mm for filling. Fixed hose connector Ø 16 mm for the breather line. Rotating hose connectors Ø 8 mm or Ø 10 mm with pick-up pipe, for fuel suction. Rotating hose connectors Ø 8 mm or Ø 10 mm for fuel return.

    (6 items) from AED 1,060.00
  • Type FTL saves considerable installation time. This connection kit has an anodized, salt water resistant aluminium lid with a counter flange and a rubber seal which is tightened very easily with just 3 bolts compressing the rubber seal to ensure a perfect seal. The set contains all the required connections, only 1 single hole with a diameter of 114 mm needs to be cut in the top of the fuel tank. This connection kit is also suitable for plastic, metal or GRP diesel or petrol fuel tanks. • Filling hose Ø38 or 51 mm and a 16 mm tank ventilation hose.• Fuel suction pipe according to model selected- Ø8 mm, max. tank depth 440 mm- Ø10 mm, max. tank depth 850 mm- Ø15 mm, max. tank depth 970 mm• Fuel return for Ø8, 10 or 15 mm hose.• Mounting flange for tank level sensors (connection is suitable for sensors with a 5-hole SAE flange).• Terminal tag 6,3 mm for earth wire.• 2 Mounting straps to secure tank.

    (6 items) from AED 589.00
  • This range of tanks is made from high-grade linear polythene, which is both rust free and less prone to condensation compared with metal tanks. The construction of the tank is seamless and therefore,can never leak. The fuel level can be seen from outside for easy checking and the tank is easily cleaned through the connection plate. Each tank is supplied with the following connections: Fixed hose connector Ø 38 mm for filling. Fixed hose connector Ø 16 mm for the breather line.Rotating hose connectors Ø 8 mm or Ø 10 mm with pick-up pipe, for fuel suction. Rotating hose connectors Ø 8 mm or Ø 10 mm for fuel return The 25, 88, 137, 335 and 390 liter models are provided with baffles, as a standard construction element.

    (5 items) from AED 574.00
  • For installation of twin tanks. With this interconnection kit 2 VETUS fuel tanks can be connected. The lid of this set has 2 connections of 16 mm for tank ventilation. 2 Brass skin fitting (G3/4) and a coupling are supplied to connect the tanks. Including 2 mounting strips to secure the tank. Suitable for Petrol & Diesel tanks. 

     AED 653.00
  • (2 items) from AED 84.00

Close

Share this page

Dear Friend,

Check out this awesome new product from Exalto Emirates!

Page: Tanks & Accessories
Share to
Your detail
Close

Specifications

Specifications

Close